Custom FR-MPP Foam Sheet Suppliers, OEM/ODM Factory - Suzhou Shincell New Material Co., Ltd.

FR-MPP Foam Sheet

Flame-retardant microcellular polypropylene foam, producing using polypropylene with flame retardants as the substrate with clean supercritical carbon dioxide as blowing agent to form a large number of microcells in the matrix.

Characteristic:

Lightweight and high strength

Clean and environmentally friendly

Good cushioning protection performance

Good surface protection performance

Good waterproof performance

Good thermal insulation performance

Good chemical resistance

Recyclable

Basic Physical Properties

Test Item	Test Method	Unit	Typical Values
Density	ISO 845:2006	g/cm³	0.03-0.10
Hot Deformation Temperature	ISO 75-2	℃	120
Thermal Conductivity	GB/T 10294-2008	W/(m*k)	0.040
Water Absorption	CNS2536-1990 THE 3RD, 10TH SECTION	%	0.10
Chemical Resistance	/	/	Resistant to strong acids and alkalis

Test results of mechanical properties

Test Item	Test Method	Unit	Multiplier
Test Item	Test Method	Unit	10P	15P	20P	25P
Density	ISO 845:2006	g/cm³	0.09	0.06	0.045	0.036
Compressive Strength (10%)	GB/T8813-2008	MPa	0.45	0.30	0.25	0.18
Flexural Strength	GB-T 8812.2-2007	MPa	0.9	0.68	0.44	0.36
Flexural Modulus	GB-T 8812.2-2007	MPa	49	33	24	18
Hardness	HG/T2489-2007	HC	81	75	66	55

Flame retardant test results

Test Item	Test Method	Residual flame time t1,s	Residual flame time t2,s	Test Result
Horizontal burning test of foam materials	UL94-2013 Clause 12	0	0	Meets HF-1 rating requirements

Application:

Battery Pack

Model airplane

Slippers

Bulletproof vest

Backpack

Pipe insulation

Shincell New Material CO.,LTD.

　　Shincell is a company dedicated to developing sustainable foaming technologies and manufacturing clean, environmentally friendly lightweight foam materials. And we also a China custom FR-MPP Foam Sheet supplier and OEM/ODM FR-MPP Foam Sheet factory. We use N2 and CO2 gases commonly found in the air to expand plastics and form a large number of micro and nano bubbles inside, a purely physical foaming process.
　　Shincell was founded by Dr. Xiulei Jiang. He started his research on supercritical fluid foaming technology at East China University of Science and Technology in 2003 and proposed the technical process of supercritical molded microcellular foaming. His early interest lies in lightweight and high-strength foam materials, and his main product is PP microcellular foam sheets. Inspired by the Adidas boost midsole derived from TPU beads foaming, he started to study the sheet foaming technology of TPU elastomer material in 2015. Based on these years of basic research, Shincell has formed two series of products: soft high-elasticity lightweight materials and hard high-strength lightweight materials.Soft high elasticity products include TPU, TPEE and PEBA, PEBAX, etc., and hard high strength products include PP, PVDF, PPO, PA, etc.

　　We focus on the research and development of foaming technology, we will continuously optimize the process, challenge our past self, improve efficiency and reduce cost, and continuously launch new products. Our foam materials are all thermoplastic and no chemical blowing agents are added in the foaming process, nor are they chemically cross-linked. We can provide our customers with online custom FR-MPP Foam Sheet products at preferential factory wholesale prices. And compared to traditional foaming materials, our foam materials are recyclable, non-toxic and environmentally friendly, and meet the needs of sustainable development!

SHINCELL

Products Recommended